Uni-Tube All Dielectric Aerial Drop cable is specifically designed for Fiber-to -the-Subscriber applications. It is a round, all dielectric cable ideally suited for self-supporting drop-type installations as well as in lashed or conduit builds. The overall glass yarn strength member is used for additional mechanical protection.
Applications:
Conduit, Duct, Aerial/Lashed.
FTTx, Access.
Product Construction
Fiber
2-24 fibers
Uni-loose tube gel -filled
Strength Member
Embedded FRP and overall fiber glass yarn.
Outer Sheath
Black UV and mo isture-resis tant p olyethy lene (PE ).
Features
Small size, Low cost. Up to 24 fibers.
Uni-tube gel-filled construction for superior fiber protection.
Two parallel FRP wire and overall glass yarn to enhance tensile resistant. and protect cable from mechanical damage.
Designed for use with inexpensive attachment hardware. Self-supported no messenger needed.
Applications
Conduit, Duct, Aerial/Lashed.
FTTx, Access.
Optical Characteristics
| Fiber Type | G.652 | G.655 | 50/125μm | 62.5/125μm | |
| Attenuation(+20℃) | 850 nm | ≤3.0 dB/km | ≤3.3 dB/km | ||
| 1300 nm | ≤1.0 dB/km | ≤1.0 dB/km | |||
| 1310 nm | ≤0.36 dB/km | ≤0.40 dB/km | |||
| 1550 nm | ≤0.22 dB/km | ≤0.23 dB/km | |||
| Bandwidth | 850 nm | ≥500 MHz·km | ≥200 Mhz·km | ||
| 1300 nm | ≥500 MHz·km | ≥500 Mhz·km | |||
| Numerical Aperture | 0.200±0.015 NA | 0.275±0.015 NA | |||
| Cable Cut-off Wavelength λcc | ≤1260 nm | ≤1450 nm | |||
Product Specification
| Fiber count | NominalDiameter(mm) | NominalWeight(kg/km) | Allowable Tensile Load(N) | Allowable Crush Resistance(N/100mm) | ||
| Short term | Long term | Short term | Long term | |||
| 2~12 | 6.5 | 35 | 1800 | 800 | 2200 | 100 |
| 12~24 | 7.0 | 40 | 1800 | 800 | 2200 | 100 |
Note:
Note: Larger spans can be achieved if necessary with installation sags larger than 1% of span.
This datasheet can only be a reference, but not a supplement to the contract. Please contact our sales people for more detailed information.
Product Construction
Fiber
2-24 fibers
Uni-loose tube gel -filled
Strength Member
Embedded FRP and overall fiber glass yarn.
Outer Sheath
Black UV and mo isture-resis tant p olyethy lene (PE ).
Features
Small size, Low cost. Up to 24 fibers.
Uni-tube gel-filled construction for superior fiber protection.
Two parallel FRP wire and overall glass yarn to enhance tensile resistant. and protect cable from mechanical damage.
Designed for use with inexpensive attachment hardware. Self-supported no messenger needed.
Applications
Conduit, Duct, Aerial/Lashed.
FTTx, Access.
Optical Characteristics
| Fiber Type | G.652 | G.655 | 50/125μm | 62.5/125μm | |
| Attenuation(+20℃) | 850 nm | ≤3.0 dB/km | ≤3.3 dB/km | ||
| 1300 nm | ≤1.0 dB/km | ≤1.0 dB/km | |||
| 1310 nm | ≤0.36 dB/km | ≤0.40 dB/km | |||
| 1550 nm | ≤0.22 dB/km | ≤0.23 dB/km | |||
| Bandwidth | 850 nm | ≥500 MHz·km | ≥200 Mhz·km | ||
| 1300 nm | ≥500 MHz·km | ≥500 Mhz·km | |||
| Numerical Aperture | 0.200±0.015 NA | 0.275±0.015 NA | |||
| Cable Cut-off Wavelength λcc | ≤1260 nm | ≤1450 nm | |||
Product Specification
| Fiber count | NominalDiameter(mm) | NominalWeight(kg/km) | Allowable Tensile Load(N) | Allowable Crush Resistance(N/100mm) | ||
| Short term | Long term | Short term | Long term | |||
| 2~12 | 6.5 | 35 | 1800 | 800 | 2200 | 100 |
| 12~24 | 7.0 | 40 | 1800 | 800 | 2200 | 100 |
Note:
Note: Larger spans can be achieved if necessary with installation sags larger than 1% of span.
This datasheet can only be a reference, but not a supplement to the contract. Please contact our sales people for more detailed information.
Non-returnable wooden drum.
Both ends of the fiber optic cables are securely fastened to the drum and sealed with a shrinkable cap to prevent ingress of moisture.
• Each single length of cable shall be reeled on Fumigated Wooden Drum
• Covered by plastic buffer sheet
• Sealed by strong wooden battens
• At least 1 m of inside end of cable will be reserved for testing.
• Drum length: Standard drum length is 3，000m±2%;
The sequential number of the cable length shall be marked on the outer sheath of the cable at an interval of 1meter ± 1%.
The following information shall be marked on the outer sheath of the cable at an interval of about 1 meter.
1. Cable type and number of optical fiber
2. Manufacturer name
3. Month and Year of Manufacture
4. Cable length
Drum marking:
Each side of every wooden drum shall be permanently marked in a minimum of 2.5~3 cm high lettering with the following:
1. Manufacture name and logo
2. Cable length
3. Fiber cable types and number of fibers,etc
4. Rollway
5. Gross and net weight
Remark: The cables are packed in carton, coiled on Bakelite & steel drum. During transportation, right tools should be used to avoid damaging the package and to handle with ease. Cables should be protected from moisture,kept away from high temperature and fire sparks,protected from over bending and crushing,protected from mechanical stress and damage.
In 2004, GL FIBER established the factory to produce optical cable products, mainly producing drop cable, outdoor optical cable, etc.
GL Fiber now have 18 sets of coloring equipments, 10 sets of secondary plastic coating equipments, 15 sets of SZ layer twisting equipments, 16 sets of sheathing equipments, 8 sets of FTTH drop cable production equipments, 20 sets of OPGW optical cable equipments, and 1 paralleling equipment And many other production auxiliary equipments. At present, the annual production capacity of optical cables reaches 12 million core-km (average daily production capacity of 45,000 core km and kinds of cables can reach 1,500 km) . Our factories can produce various types of indoor and outdoor optical cables ( such as ADSS, GYFTY, GYTS, GYTA, GYFTC8Y, air-blown micro-cable, etc.). the daily production capacity of common cables can reach 1500KM/day, the daily production capacity of drop cable can reach max. 1200km/day, and the daily production capacity of OPGW can reach 200KM/day.
Open Whats App